Here it is for the ultimate in performance, control and tunabilty! Our Stage 2 progressive fender/firewall mount system comes with the most advance water alcohol/methanol controller on the market hands down. Designed specifically for those who want the best performance with a fender/firewall mounted system. This is a excellent choice for low to high boost applications, intercooled or non-intercooled, who are looking for the biggest increases in octane inhancement, reduction in air charge temperatures and detonation suppresion through out their rpm range.
Engineered specifically for both carbureted and EFI forced induction applications. Our Stage 2 progressive fender/firewall mount water/alcohol injection system is as simple as it gets. Once installed, operation is very simple. Simply begin by running a boost signal from manifold pressure to the boost port (brass nibble) located on the side of the programmer. From there you can quickly set the activation point, from 1-30psi, using the green knob. Next, the middle gray knob (Tune) with 10 positions allows you to control the maximum duty cycle of the pump. This is great for fine tuning in situations where you need to lower or raise the flow. Lastly, you have the red knob which allows you to control the rate of increase. For example, setting it a 15psi would allow the system to go into full flow once 15psi was reached. You can also bring the system in quicker by setting the red knob sooner. For example, setting the red knob at 10 psi even though the motor actually reaches 15 psi. This will increase rate of increse and vise versa.
Once activated the system will spray a progressive amount of fluid through the nozzle or nozzles based on the custom map you have set. Flow will also reduce perportionally as boost drops off and will not turn off untill boost drops back down below the set activation point. Users can also turn the system into a two demensional system by including any of the following 0-5v inputs; TPS, MAF, MAP, EGT and AIT, for even greater control and custom mapping which isn't offered by the competitors systems.
While others claim to be the industry leader in water alcohol/methanol injection we bring it to you. Compare for yourself against the competitors systems and you'll quickly recognize the difference and why this is the most advance, most featured packed, easiest to use progressive water alcohol/methanol system on the market. Designed for the average street enthusists or the avid racer it packs hardcore racing features such as:
AIS Features vs. Leading Competitors:
100% digital processor for lighting fast response
Quick, easy to use knobs for adjusting activation settings, maximum duty cycle, and rate of increase - no screw driver required like the competitors programmer
Industries only true 2-demensional programmer allowing you to run a boost signal in conjuction with any of the following 0-5v input signals; TPS, MAF, MAP, EGT and AIT
Industries only water alcohol/methanol injectiion controller on the market with a built in data logger
Built in status monitor unlike the competitors
Built in serial port for connecting laptop
Free WIndows based software available
Pre-wired ready to go unlike the competitors
Lower Air Temps By 50-200+ Degrees & Increase Power 10-15% With ONLY Windshield Wiper Fluid!
That's right! Using nothing more then windshield wiper fluid you can quickly achieve the benefits of a water/methanol injection system. Best of all, it's very easy to locate just about anywhere in the states and cost only $2.00-$3.00 per gallon. But not just any windshield wiper fluid will do. You'll need to buy the windshield wiper fluid that is rated for negative 20 degrees or greater below zero. It is only this windshield wiper fluid, which contains a 50% content or greater of methanol. Using strictly windshield wiper fluid you can expect to see a 50-200+ degree drop in air intake charge temperatures on supercharged and turbocharged engines with horsepower gains ranging from 10-15% are common. (temperature drops and horsepower gains vary depending on engine build, type supercharger or turbocharger used, amount of boost and intercooled or non-intercooled)
System Contents Include:
Completely adjustable digital progressive controller
2 quart 100% alcohol compatible tank
150 psi Shurflo pump with EPDM seals for 100% methanol or alcohol
- Check valve with quick disconnects
- Quick connect tank adapter fitting
- 15 ft of black high pressure fluid tubing
- 15 ft of black high pressure vacuum tubing
- 15 ft of electrical wire
- Nickel plated injector
- Two different size nozzles
- Relay with wiring harness
- Fuse holder with fuse
- 8 large zip ties
- 5 small zip ties
- Vacuum tee fitting
- 2 ft of high temperature wire loom
- Hardware for securing pump
Benefits Of Water Alcohol/Methanol Injection:
Lower air temperatures by 50-250+ degrees
Reduces cylinder temperatures up to 300+ degrees
Increase your 87-93 pump gas by 8-20+ points
Increase horsepower safely by 10-15%
Allows you to safely run more boost and timing
Longer more stable combustion expansion and progression
Removes carbon build up from combustion chambers, pistons and valves
Reduces & helps eliminate engine damaging detonation & pre-ignition
No need for expensive racing fuel or additives
Important Notes:
Installation Time:
Availability:
Warranty:
AIS warrants this system free of defects for up to 1 year after purchase. See AIS policy & warranty page for complete details.
