Here it is for the ultimate in control and tunabilty! Our Stage 2 progressive system is the most advance watermethanol controller on the market hands down. While others claim to be the industry leader in water methanol injection we bring it to you. Designed for the average street enthusists or the avid racer it packs hardcore racing features such as:
Compare for yourself against the competitors systems and you'll quickly recognize the difference and why this is the most advance, most featured packed, easiest to use and install progressive water alcohol system on the market.
Engineered specifically for both carbureted and EFI forced induction applications. Our Stage 2 boost activated system is as simple as it gets. Once installed, operation is very simple. Simply begin by running a boost signal from manifold pressure to the boost port (brass nibble) located on the side of the programmer. From there you can quickly set the activation point, from 1-30psi, using the green knob. Next, the middle gray knob (Tune) with 10 positions allows you to control the maximum duty cycle of the pump. This is great for fine tuning in situations where you need to lower or raise the flow. Lastly, you have the red knob which allows you to control the rate of increase. For example, setting it a 15psi would allow the system to go into full flow once 15psi was reached. You can also bring the system in quicker by setting the red knob sooner. For example, setting the red knob at 10 psi even though the motor actually reaches 15 psi. This will increase rate of increse and vise versa.
Once activated the system will spray a progressive amount of fluid through the nozzle or nozzles based on the custom map you have set. Flow will also reduce perportionally as boost drops off and will not turn off untill boost drops back down below the set activation point. Users can also turn the system into a two demensional system by including any of the following 0-5v inputs; TPS, MAF, MAP, EGT and AIT, for even greater control and custom mapping which isn't offered by the competitors systems.
Industries First Trunk Mount Water Methanol Injection System
You literally can't beat the performance, quality and value of this system. This is undoubtedly the easiest to install water methanol injection system on the market. Our trunk mount kits now come completely pre-assembled making it easier then ever before to install, hook up and run. No longer do you need to worry about installing the pump, container, hoses and wiring under the hood like our competitors systems. All that is required by you is to strap it down, put power to it, run the vacuum and high-pressure line, install the nozzle and begin tuning. It's that easy!
Compare To The Competitors Systems And See The Difference
Once you compare our trunk mount systems to the competitors under the hood systems you will quickly recognize the advantage and ease of installation with our systems. With installation times as quick as 60-90 minutes our pre-assembled and pre-wired systems are 4-6 times faster then the competitors unassembled systems. No longer do you have to install the pump, reservoir, tubing and wiring under the hood for an unsightly appearance. Our trunk mount systems completely relocate everything into the trunk for a stealthy, clean installation. No one has to know you even have it!
No Space Under Your Hood...No Problem
It is becoming increasingly harder and harder to find space under the hood of today's cars. While many cars often do have the space to install a small container and pump under their hood this can be unsightly to some and take away from the car's appearance under the hood and let others know that you have it. Often time's space does not permit the use of an additional container under the hood. A common solution used by many is converting the vehicles existing windshield wiper fluid container for use with the water methanol/alcohol injection. This completely compromises the use of the windshield wiper feature. We feel this is hardly a solution and simply a short cut used by others. Our trunk mount kit completely solves all of these issues by relocating everything cleanly in the trunk of your vehicle.
Lower Air Temps By 50-200+ Degrees & Increase Power 10-15% With ONLY Windshield Wiper Fluid!
That's right! Using nothing more then windshield wiper fluid you can quickly achieve the benefits of a water/methanol injection system. Best of all, it's very easy to locate just about anywhere in the states and cost only $2.00-$3.00 per gallon. But not just any windshield wiper fluid will do. You'll need to buy the windshield wiper fluid that is rated for negative 20 degrees or greater below zero. It is only this windshield wiper fluid, which contains a 50% content or greater of methanol. Using strictly windshield wiper fluid you can expect to see a 50-200+ degree drop in air intake charge temperatures on supercharged and turbocharged engines with horsepower gains ranging from 10-15% are common. (temperature drops and horsepower gains vary depending on engine build, type supercharger or turbocharger used, amount of boost and intercooled or non-intercooled)
110+ Plus Octane With ONLY Wind Shield Wiper Fluid!
Thats right! Using nothing more then windshield wiper fluid as listed above you can effectively increase your 91-93 octane pump gas by 10-20+ points dramatically increasing your fuels octane rating well over 100+ octane. No need for expensive racing fuels which can cost as much as $16.00 per gallon at some race tracks. Windshield wiper fluid cost's only $2.00-$3.00 per gallon. Even better our 1.5 gallon trunk mount container will last up to 2-3 weeks before needing to be refilled on a typical 500-600 horsepower supercharged or turbocharged motor costing you only pennies more per gallon to have 100+ octane.
Water Alcohol/Methanol Injection = Cheap Insurance For Your Motor
You wouldn't drive your car with out car insurance. Now theres insurance for your motor. Protect your motor and the investment you have in your motor with proven lower air intake charge temperturtes by 50-200+ degrees and increased octane by 10-20+ points. Together this will reduce and help eliminate engine damaging detonation. It's cheap insurance for your motor.
System Contents Include:
Completely adjustable digital progressive controller
Custom molded 3 gallon tank designed specifically for our pump
250 psi pump with EPDM seals for 100% methanol or alcohol
Heavy duty check valve with quick disconnects
20 ft of black high pressure tubing
20 ft of electrical wire
2 rubber grommets
Nickel plated threaded injector holder
Interchangeable injector sized to application
Fuse holder with fuse
Two brushed aluminum tank straps
All necessary hardware
Detailed instruction manual with pictures
Benefits Of Water Alcohol/Methanol Injection:
Lower air temperatures by 50-250+ degrees
Reduces cylinder temperatures up to 300+ degrees
Increase your 87-93 pump gas by 8-20+ points
Increase horsepower safely by 10-15%
Allows you to safely run more boost and timing
Longer more stable combustion expansion and progression
Cools and protects the tops of your pistons and upper ring
Removes carbon build up from combustion chambers, pistons and valves
Reduces & helps eliminate engine damaging detonation & pre-ignition
No need for expensive racing fuel or additives
Features vs. Leading Competitors:
Most advanced progressive controller on the market - compare for yourself vs the competitors
System comes pre-assembled unlike the competitors which requires you to assemble everything
System can be installed in 90 minutes - Thats 4-5 times faster vs. the competitors under hood kit
No unsightly pump, reservoir, hoses or added wiring under the hood
No need to convert existing wind shield wiper fluid container
Our system is completely hidden in the trunk for a stealthy install
3 gallon container vs. the competitors common 1-2 quart container
Much less frequent refills required as the leading competitors do
Important Notes:
Installation Time:
Availability:
Warranty:
AIS warrants this system free of defects for up to 1 year after purchase. See AIS policy & warranty page for complete details.
